Specifications
| Type | Description |
|---|---|
| Part Number | DRV5053 |
| Manufacturer | Texas Instruments |
| Product Type | Analog bipolar Hall effect sensor |
| Category | Sensor |
| Package / Case | SOT-23 (DBZ) 3-pin, 2.92 mm x 1.30 mm body; TO-92 (LPG) 3-pin, 4.00 mm x 3.15 mm body |
| Magnetic Sensing Type | Linear analog bipolar Hall effect sensor; chopper-stabilized Hall IC |
| Output Response Range | 0 V to 2 V analog output; responds linearly to applied magnetic flux density and distinguishes field polarity |
| Output Voltage at Zero Magnetic Field | 1 V at B = 0 mT |
| Output Voltage Range | 0.2 V to approximately 1.8 V, amplified output stage |
| Supply Voltage Operating Range | 2.5 V to 38 V; no external regulator required |
| Operating Ambient Temperature | -40°C to 125°C, Q temperature grade |
| Power-On Time | 35 µs typ, 50 µs max over operating free-air temperature range |
| Output Current Sink Capability | 2.3 mA, amplified output stage / overcurrent protection sinking current |
| Output Current Source Capability | 300 µA, amplified output stage / overcurrent protection sourcing current |
| Reverse Supply Protection | Up to -22 V; specified by design, tested to -20 V |
| Load Dump Support | Up to 40 V protection feature |
| Power Supply Voltage Absolute Maximum | -22 V min, 40 V max over operating free-air temperature range |
| Supply Voltage Ramp Rate Absolute Maximum Below 5 V | Unlimited for VCC < 5 V |
| Supply Voltage Ramp Rate Absolute Maximum Above 5 V | 0 to 2 V/µs for VCC > 5 V |
| Output Pin Voltage Absolute Maximum | -0.5 V min, 2.5 V max over operating free-air temperature range |
| Output Pin Reverse Current During Reverse Supply | 0 to -20 mA under reverse supply condition |
| Magnetic Flux Density Absolute Maximum | Unlimited, BMAX |
| Operating Junction Temperature Absolute Maximum | -40°C to 150°C, TJ |
| Storage Temperature | -65°C to 150°C, Tstg |
| ESD HBM Rating | ±2500 V, ANSI/ESDA/JEDEC JS-001, all pins |
| ESD CDM Rating | ±500 V, ANSI/ESDA/JEDEC JS-002, all pins |
| Recommended Output Pin Voltage | 0 V to 2 V, OUT pin |
| Recommended Output Source Current | 0 to 300 µA, OUT pin |
| Recommended Output Sink Current | 0 to 2.3 mA, OUT pin |
| Supply Current | 2.7 mA typ at VCC = 2.5 V to 38 V, TA = 25°C |
| Supply Current at High Temperature | 3 mA typ, 3.6 mA max at VCC = 2.5 V to 38 V, TA = 125°C |
| Output Delay Time | 13 µs typ, 25 µs max at TA = 25°C |
| Quiescent Output Voltage | 0.9 V min, 1.02 V typ, 1.15 V max at B = 0 mT, TA = -40°C to 125°C |
| Bandwidth | 20 kHz magnetic field detection bandwidth |
| Input-Referred Noise | 0.40 mTpp min, 0.49 mTpp typ, 0.79 mTpp max; COUT = 50 pF, TA = -40°C to 125°C; not production tested |
| Linearity | 1% for -BSAT < B < BSAT |
| Minimum Output Saturation Voltage | 0.2 V for B < -BSAT |
| Maximum Output Saturation Voltage | 1.8 V for B > BSAT |
| DRV5053OA Sensitivity | -17.5 mV/mT min, -11 mV/mT typ, -5 mV/mT max at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053OA Output-Referred Noise | 5 mVpp at VCC = 3.3 V, ROUT = 10 kΩ, COUT = 50 pF, TA approximately -40°C to 125°C |
| DRV5053OA Input Saturation Field | 73 mT at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053PA Sensitivity | -35 mV/mT min, -23 mV/mT typ, -10 mV/mT max at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053PA Output-Referred Noise | 11 mVpp at VCC = 3.3 V, ROUT = 10 kΩ, COUT = 50 pF, TA approximately -40°C to 125°C |
| DRV5053PA Input Saturation Field | 35 mT at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053RA Sensitivity | -70 mV/mT min, -45 mV/mT typ, -20 mV/mT max at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053RA Output-Referred Noise | 22 mVpp at VCC = 3.3 V, ROUT = 10 kΩ, COUT = 50 pF, TA approximately -40°C to 125°C |
| DRV5053RA Input Saturation Field | 18 mT at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053VA Sensitivity | -140 mV/mT min, -90 mV/mT typ, -45 mV/mT max at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053VA Output-Referred Noise | 44 mVpp at VCC = 3.3 V, ROUT = 10 kΩ, COUT = 50 pF, TA approximately -40°C to 125°C |
| DRV5053VA Input Saturation Field | 9 mT at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053CA Sensitivity | 10 mV/mT min, 23 mV/mT typ, 35 mV/mT max at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053CA Output-Referred Noise | 11 mVpp at VCC = 3.3 V, ROUT = 10 kΩ, COUT = 50 pF, TA approximately -40°C to 125°C |
| DRV5053CA Input Saturation Field | 35 mT at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053EA Sensitivity | 20 mV/mT min, 45 mV/mT typ, 70 mV/mT max at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DRV5053EA Output-Referred Noise | 22 mVpp at VCC = 3.3 V, ROUT = 10 kΩ, COUT = 50 pF, TA approximately -40°C to 125°C |
| DRV5053EA Input Saturation Field | 18 mT at VCC = 3.3 V, TA approximately -40°C to 125°C |
| DBZ Junction-to-Ambient Thermal Resistance | 333.2°C/W, SOT-23, 3 pins |
| LPG Junction-to-Ambient Thermal Resistance | 180°C/W, TO-92, 3 pins |
| DBZ Junction-to-Case Top Thermal Resistance | 99.9°C/W, SOT-23, 3 pins |
| LPG Junction-to-Case Top Thermal Resistance | 98.6°C/W, TO-92, 3 pins |
| VCC Pin Function | 2.5 V to 38 V power supply; bypass to GND with 0.01 µF minimum ceramic capacitor rated for VCC |
| OUT Pin Function | Hall sensor analog output; 1 V output corresponds to B = 0 mT |
| Datasheet Status | request_only |
Product Overview
The DRV5053 is a Texas Instruments analog bipolar Hall effect sensor built as a chopper-stabilized Hall IC. Its output responds linearly to applied magnetic flux density and distinguishes field polarity. At zero magnetic field, the OUT pin is centered at 1 V, while the recommended OUT pin range is 0 V to 2 V and the amplified output stage saturates near 0.2 V and 1.8 V.
The device operates from a 2.5 V to 38 V supply without an external regulator and is specified for -40°C to 125°C ambient operation in the Q temperature grade. Electrical timing includes 35 µs typical power-on time, 13 µs typical output delay, and 20 kHz magnetic field detection bandwidth. Output drive capability is specified at 300 µA source and 2.3 mA sink.
Package options include the 3-pin SOT-23 DBZ package and 3-pin TO-92 LPG package. The VCC pin should be bypassed to GND with at least a 0.01 µF ceramic capacitor rated for VCC, and the OUT pin provides the Hall sensor analog output.
Key Features
- Linear analog bipolar Hall effect sensing
- Chopper-stabilized Hall IC architecture
- 0 V to 2 V analog output response
- 1 V output at zero magnetic field
- 2.5 V to 38 V supply operation
- -40°C to 125°C ambient operating range
- 20 kHz magnetic field detection bandwidth
- 35 µs typical power-on time
- 13 µs typical output delay at 25°C
- Reverse supply protection up to -22 V
- Load dump support up to 40 V
- SOT-23 and TO-92 3-pin package options
Typical Applications
- Linear magnetic field measurement
- Bipolar magnetic polarity detection
- Analog Hall sensor output circuits
- 3.3 V magnetic sensing designs
- Wide-supply sensor interfaces
- SOT-23 sensor assemblies
- TO-92 sensor assemblies
- Fast power-on magnetic sensing
Procurement Notes
When requesting a quote for DRV5053, buyers should confirm the manufacturer, package or case, required quantity, target date code, compliance documents, packing method, destination country and expected delivery schedule.
If alternatives are acceptable, buyers should share the approved vendor list, required electrical or optical limits, package constraints and qualification requirements. Any alternative part should be reviewed by the buyer's engineering team before production use.
For analog and signal-chain sourcing, supply voltage, bandwidth, accuracy, noise level, package, temperature grade, input/output configuration and qualification requirements should be verified before approval.
FAQ
What type of sensor is the DRV5053?
The DRV5053 is an analog bipolar Hall effect sensor from Texas Instruments. It uses a chopper-stabilized Hall IC and provides a linear analog output response to applied magnetic flux density while distinguishing magnetic field polarity.
What supply voltage range does the DRV5053 support?
The DRV5053 operates from a 2.5 V to 38 V supply range with no external regulator required. Its absolute maximum power supply voltage range is specified from -22 V minimum to 40 V maximum.
What is the DRV5053 output at zero magnetic field?
At B = 0 mT, the DRV5053 output is centered at 1 V. The specified quiescent output voltage across -40°C to 125°C is 0.9 V minimum, 1.02 V typical, and 1.15 V maximum.
Which package options are listed for the DRV5053?
The listed package options are SOT-23 (DBZ) 3-pin with a 2.92 mm x 1.30 mm body and TO-92 (LPG) 3-pin with a 4.00 mm x 3.15 mm body.
Technical Review & Sourcing Note
Prepared by LDeepAI Component Sourcing Team. Reviewed for RFQ, documentation and alternative sourcing use. Last updated: July 7, 2026.
This page is based on manufacturer datasheet information and LDeepAI sourcing review. Specifications should be verified against the official manufacturer datasheet before final procurement or design approval. Final electrical, optical and reliability approval should be confirmed by the buyer's engineering team.